23-06-2015 04:06 PM | ||
Unregistered |
Quote:
|
|
23-06-2015 01:42 PM | ||
Unregistered | what made you condemn it so much? | |
23-06-2015 11:13 AM | ||
Unregistered | UniSIM is already bad enough, to take it as part time is doubly worse. That's like a notch better than degree mill. | |
23-06-2015 09:30 AM | ||
Unregistered | If u r local, can consider UniSIM part time degree... Heavily subsidies and you can take it at your own pace.. Up to 8 years to complete it | |
23-06-2015 07:21 AM | ||
Unregistered |
4322 I was doing ops previously and had increasingly low job satisfaction. I am in my 30s, kind of in a mid life crisis. If possible, I would like to move out from ops but tough, as that's where my experience lies. If I apply for ops roles, I may still get some calls from recruiters. Otherwise, none. Another issue I sense is that companies would rather hire cheaper and younger staff for ops. I am unsure what jobs I can switch to? Or should I look for ops roles, still? Thanks. |
|
07-05-2015 04:00 PM | ||
Unregistered |
i suggest u not waste ur time. honestly with this kind of diploma grade & only work exp at junior level that is not even consider exec, the only deg u can get are those low rep like mdis, kaplan, shri etc. they are not very cheap either, to buy that deg can cost 12k upwards which is silly becase the starting pay for this type of deg grad is barely 2.2-2.5k in pte sector. the few hundred extras u can get aint enough to pay off the study loan. also this kind of deg very hard to compete if u wana join civil service MX scheme or stat board Div I officer. also there is no guarantee taking this kind of generic deg can actually help in the career. u r better off just slowly gaining work exp, to get 2.8-3k by 30 is still possible. |
|
07-05-2015 03:15 PM | ||
Unregistered |
Let's be honest here. With grades like that, you are either not cut out academically or are in the wrong course altogether. What do you hope to study? What do you hope to do? Your best bet is private after getting some work experience. |
|
07-05-2015 01:01 PM | ||
aplover |
i wanted to say you can try to buy SPU degree and apply for IDA. They have no right to reject it now since they publicly admit it's a proper uni. In fact, the whole Civil Service and stat boards should have similar standards and accept SPU degree now. But i will give you proper advise. Yes, there's a difference in perception of degrees. SIM or private unis are below the local unis. But so are the local unis considered lower than ivy league ones. But qualifications only help you so far in the 1st couple of steps in your career. Later on it's about what you do with your career and how you build it up. I believe in getting a degree even though it's now so common but it still separates the normal staff and the supposed higher potential staff. The difference in a masters and a bachelor is less perceptible, so just aim for a bachelor's degree. If i were you, i would focus hard on working well. See whether you can grow internally in your company. Move to a bigger company and work smart. Save up money and study part time or if you can afford it, quit and study full time in a local uni like NUS/NTU/SMU/SUTD/SIT. If you choose to still hone your skills in the engineering sector, focus on getting a degree in NUS or NTU. |
|
07-05-2015 12:53 PM | ||
Unregistered |
Quote:
Second check that getting a degree, even a private one, will help you advance in your career. Overseas uni could cost you 50k/year. If you go for a 2 year course, that's 100k in debt. You might need to repay 1k/month for 10 years to fully pay it off. Imagine if your salary remains at 2xxx, how are you going to survive with half of your salary going towards loan repayment? There are also private degree courses by places like Kaplan in SG, worth a try for the lower cost. |
|
07-05-2015 12:27 PM | ||
Unregistered |
Whatever degree you choose to take, please confirm with HR first. If not take already, then not recognize, it will be a waste of money. |
|
This thread has more than 10 replies. Click here to review the whole thread. |